Air Conditioning Repair in Riverside, CA

Like any hardworking appliance, your home’s air conditioning system will eventually need some professional repairs and maintenance to keep it humming along. But figuring out what those AC repair costs may run can feel like rolling the dice. While every situation is different, here’s a general sense of what to expect when it comes to pricing some common cooling system fixes:

Minor Part Replacements

On the lower end of the spectrum, something like replacing a failed AC contactor, run capacitor or thermostat typically falls into the basic service fee range. These smaller components don’t require extensive labor.

Electrical System Repairs

When you start getting into more complex electrical diagnostic work and repairs to circuit boards, wiring issues or the compressor’s motor, those jobs tend to get pricier due to the labor hours involved.

Refrigerant Leaks

If your system is low on refrigerant, having a technician locate the leak source, repair it, and properly recharge the unit can get expensive quickly based on refrigerant costs and labor time.

Compressor Replacements

The compressor is the heart of your AC system, so a full compressor swap is typically one of the most costly repairs you may face. Compressors themselves are pricey, and the labor is intensive.

Coil Replacements

Whether it’s the indoor evaporator coil or outdoor condenser coils, replacing leaking or damaged coils is a big job. You’re paying for the coil itself, plus extensive labor hours to make the swap.

The best way to get an accurate idea of potential AC repair costs is to have a certified technician from All Pro come out and thoroughly diagnose the issue. We’ll provide an upfront, honest assessment and pricing options so you can make an informed decision. Proper routine maintenance also helps avoid surprise breakdowns.

When your home’s air conditioning system starts acting up or underperforming, it’s never a good idea to just ignore those issues and keep on running the unit. Doing so can potentially lead to much bigger and more costly headaches down the road. Here are some of the major risks of neglecting needed AC repairs:

Decreased Energy Efficiency

Even seemingly minor problems like refrigerant leaks or failed components can force your air conditioner to work harder and run longer cycles to produce the same cooling output. Those increased runtimes drive your utility costs through the roof.

Premature System Failure

The longer you operate your AC equipment when it’s compromised, the more strain you’re putting on other components. This accelerated wear-and-tear can cause a domino effect of breakdowns and shorten your system’s overall lifespan significantly.

Safety Hazards

Electrical issues, refrigerant leaks, condensate drain backups – all these AC problems create potential safety risks for your home and family if they persist and worsen. Fires, indoor air quality dangers, and water damage are all possibilities.

Costlier Repairs Down the Line

Addressing a repair need promptly when it’s still relatively minor is always cheaper than waiting for it to escalate into a more catastrophic failure. What may have been an affordable fix can turn into an expensive nightmare.

Voided Equipment Warranties

Most manufacturer warranties require you to perform routine maintenance and repairs to keep coverage valid. If you ignore issues and something major fails, the manufacturer can deny your claim since you failed to properly maintain the system.

While AC repair needs are never ideal, putting them off only makes the situation worse. The professionals at All Pro can quickly diagnose any cooling issue and have your system operating reliably again at a fraction of the cost of a full replacement down the line. Don’t let AC problems linger!

There’s nothing more frustrating than walking from one perfectly chilled room in your Riverside home to another that feels like a sauna. Uneven cooling and hot/cold spots are a common complaint, even with a new high-efficiency AC installation. The good news is there are some simple steps you can take to help even out those temperature imbalances:

Check Air Vents/Registers

One of the biggest culprits for hot rooms is blocked or closed air vents and registers. Do a walkthrough and ensure all vents are fully opened and unobstructed by furniture or other objects restricting airflow to those spaces.

Replace Air Filters

Dirty, clogged air filters make your HVAC system work harder to move air through the ductwork. Changing them out monthly can really help with consistent airflow.

Seal Duct Leaks

Over time, those air ducts running through attics and crawlspaces can spring leaks that allow conditioned air to escape before reaching vents. Having the All Pro team inspect and reseal ductwork can make a big difference.

Add Insulation

Poorly insulated rooms, especially those over garages or with lots of windows, will always struggle with temperature variations. Having extra insulation installed can help them retain that cooled air better.

Install Ductwork Dampers

If you’ve got a couple of chronically hot rooms, your ductwork may just need some manual dampers installed. These allow you to adjust airflow and redirect more cooling to those problem areas.

Upgrade to Zoning System

For true customized cooling, you may want to consider having the All Pro team install a zoned HVAC system with multiple thermostats. This allows you to control temperatures independently in different areas of your home.

Don’t just resign yourself to dealing with hot and cold rooms! The team at All Pro can take a look at your ductwork design and suggest affordable solutions to help even out cooling distribution throughout your entire home sweet home.

As the hardworking heart of your air conditioning system’s air distribution, that blower motor certainly takes a beating over the years. When it finally gives up the ghost, you’ll be left with little to no airflow coming from your vents and registers. But what exactly causes these crucial AC components to fail prematurely? Here are some of the most common culprits:

Overheating

Blower motors generate a lot of heat during normal operation. But when airflow gets restricted by things like dirty air filters or blocked ductwork, that heat has nowhere to escape. This excessive overheating can cause the motor’s windings to burn out over time.

Worn Bearings

Those blower motor bearings allow the shaft to spin smoothly and circulate air. As they become dry, pitted or worn down, they create excess friction and grinding that robs the motor of efficiency until it eventually seizes up completely.

Moisture Issues

While blower assemblies are designed to withstand some moisture and condensation, excessive water exposure can wreak havoc. Leaky drain pans or piping can allow moisture to accumulate in the blower casing, leading to premature corrosion and electrical shorts.

Age/Overuse

Like any mechanical equipment with moving parts, blower motors simply have a finite usable lifespan based on the number of run hours and cycles over the years. Once they hit that threshold, failure becomes increasingly likely even with proper maintenance.

Power Inconsistencies

Erratic power supply issues like voltage fluctuations, surges, and electrical shorts can damage delicate blower motor windings over time. This weakens the motor until it no longer has enough torque to turn the blower wheel properly.

While routine AC maintenance helps maximize blower motor lifespan, they’ll inevitably need replacement. The All Pro team has the experience to properly diagnose blower failures and get your system’s airflow back up and running quickly.

When your home’s new air conditioning system just isn’t quite delivering the cooling performance and comfort you expected, it’s easy to immediately point the finger at the AC equipment itself. But before assuming your new installation is to blame, you may want to consider another potential culprit – your thermostat.

As the control center for your entire cooling setup, thermostats play a crucial role in ensuring your AC runs properly and maintains those desired temperature levels. If the thermostat isn’t functioning correctly or is improperly programmed, it can absolutely cause all sorts of comfort issues. Here are some signs that faulty thermostat could be the root of your AC woes:

Erratic Temperature Swings

Is your home going through hot/cold cycles where temps fluctuate wildly rather than holding steady? That’s a red flag that thermostat isn’t properly reading temperatures or sending accurate cooling signals.

System Constantly Running

If your AC just never seems to cycle off and is running around the clock, chances are the thermostat isn’t registering when set temperatures are reached and continuing to call for cooling unnecessarily.

No Response From System

Conversely, if you’re adjusting that thermostat but getting zero response from your AC equipment at all, there’s likely a wiring issue or other internal thermostat failure preventing it from communicating.

Inconsistent Temperatures

Are some rooms significantly warmer or cooler than others, despite all vents being open? Thermostats can have trouble accurately reading temperatures if installed in poor locations.

Short Cycling Issues

An improperly calibrated thermostat can cause that classic short cycling issue where your AC only runs for brief periods before shutting off repeatedly. This puts serious strain on components.

If you’re experiencing any of those AC control issues after a new installation, the thermostat could very well be the root cause. The All Pro team will thoroughly inspect your thermostat wiring and programming to identify potential problems and get your system running like it should.

There’s nothing worse than going to crank up the AC on a scorching Riverside afternoon only to find the system has frozen over, leaving you stuck in the sweltering heat. While a frozen evaporator coil usually signals an underlying issue requiring professional repair, there are some simple preventative measures you can take as a homeowner to avoid this maddening situation:

Filter Maintenance

Clogged air filters are one of the prime culprits behind frozen AC coils. When airflow is restricted, it causes the cooling system to work harder, leading to increased cold temperatures and potential freezing. Changing those filters every 30-90 days is an easy preventative step.

Keep it Clear

In addition to the filters, you’ll want to routinely inspect and clean off any built-up dust, dirt or debris around the outdoor condenser unit and indoor evaporator coil. Obstructions blocking airflow can quickly lead to freeze-ups.

Clearance is Key

Make sure to provide adequate clearance around that exterior condenser, removing any plants, fencing or structures that could be restricting air intake. The unit needs proper breathing room to expel heat efficiently.

Adjust Fan Operation

Many thermostat models let you toggle the fan between “Auto” and “On” modes. Running the fan continuously can help prevent overly cooled air from settling around the coil and freezing up.

Check Ductwork

Damaged or poorly insulated ductwork can cause cooled air to lose temperature as it travels through attics or crawlspaces. This allows moisture to freeze on the coil. Sealing and insulating ducts is an easy fix.

While taking these preventative steps helps, sometimes a frozen AC is the result of a bigger problem like a refrigerant leak or failed component. If you do experience a freeze-up, don’t try hacking at the ice yourself – call in the professionals at All Pro right away. We’ll get to the root of the issue quickly to restore reliable cooling.